10 gbps 40km multirate xfp transceiver preliminary XP-MR-04-CDA 1 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 luminentoic.com lumnds644-nov0106 rev. 0. 1 features ? xfp msa rev 4.5 compliant ? 40km reach ? supports 9.95gb/s, 10.31gb/s, 10.52gb/s, 10.7 gb/s , and 11. 1gb/s ? cooled eml with isolator ? pin receiver ? power dissipation <3.5w ? -5 to 70 c temperature range ? digital diagnostics ? xfi high speed electrical interface ? rohs compliant ? class 1 laser, 21cfr 1040.10/1040.11 ? en 60825-1/a1:2002 compliant ? bail latch color: white parameter symbol min typical max unit supply voltage (1.8v) v cc 2 1.71 1.8 1.89 v supply voltage (3.3v) v cc 3 3.14 3.3 3.47 v supply voltage (5v) v cc 5 4.75 5 5.25 v total current on any pin i cc - - 500 ma inrush current (1.8v) i inrush 2 - - 1 a inrush current (3.3v) i inrush 3 - - 0.75 a inrush current (5v) i inrush 5 - - 0.5 a module current ramp rate - - 100 ma/s power on 1.8v rail p 2rail - - 1.8 w power on 3.3v rail p 3rail - - 2.5 w power on 5v rail p 5rail - - 2.5 w module total power consumption p t - - 3 .5 w power consumption-p_down mode p p_d - - 1.5 w power supply noise rejection psnr compliant to section 2.7.2 of xfp msa bit rate br 9.95 - 11.1 gb/s operating temperature (case) t op -5 - 70 oc strorage temperature t st -40 - 85 oc general operations parameter symbol min typical max unit maximum supply voltage (3.3v) vcc3 -0.3 - 3.6 v maximum supply voltage (5.0v) vcc5 -0.3 - 5.5 v maximum supply voltage (1.8v) vcc2 -0.3 - 2 v storage temperature t st -40 - 85 oc absolute maximum rating a) peak to peak noise when measured with a 1 mhz low pass ? lter b) peak to peak noise when measured with 1mhz-10mhz low pass ? lter
10 gbps 40km multirate xfp transceiver preliminary XP-MR-04-CDA 2 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 luminentoic.com lumnds644-nov0106 rev. 0. 1 parameter symbol min typical max unit out put power p o -1 0.5 2 dbm average launch power tx_off p off - - -30 nm extinction ratio er 8.2 - - db eye mask itu-t g.691, telcordia gr-253-core, ieee802.3 10gbase-zr compliant side mode suppression ratio smsr 30 - - db wavelength 1530 1565 nm spectral width ? 20 - - 1 nm jitter generation (peak-to-peak) j gen(pk-pk) - - 0.1 ui jitter generation (rms) j gen(rms) - - 0.01 ui dispersion penalty at 800 ps/nm dp - - 2 db relative intensity noise rin - - -130 db/hz re? ectance tolerance ref t - - -27 db transmitter speci? cations (optical) parameter symbol min typical max unit sensitivity (9.95gb/s) a rx sens995 - - -16 dbm sensitivity (10.7gb/s) a rx sens1070 - - -15 dbm overload a rx ol 0 - - dbm wavelength b 1528 - 1565 nm optical return loss orl - - -27 db los assert - -24 - - dbm los de-assert - - - -16 dbm los hysteresis - 0.5 - - db receiver speci? cations (optical) a ) at 8.2db er, 1e-12 ber, 2 31 -1 prbs, back to back b) operational over 1200 - 1625nm range parameter symbol min typical max unit input differential impedence r in - 100 - ? differential data input swing v in,p-p 120 - 820 mv txdisable_disable vd 2 - vcc3 v txdisable_enable ven gnd - gnd + 0.8 v transmitter speci? cations (electrical) parameter symbol min typical max unit reference differential output impedence z d - 100 - differential data output swing v out,p-p 340 - 850 mv output rise time, 20-80% t r 24 - - ps output fall time, 20-80% t f 24 - - ps los fault v los_fault host_vcc3 - 0.5 - host_vcc3 v los normal v los_normal gnd - gnd + 0.4 v receiver speci? catioins (elelctrical)
10 gbps 40km multirate xfp transceiver preliminary XP-MR-04-CDA 3 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 luminentoic.com lumnds644-nov0106 rev. 0. 1 parameter symbol min typical max unit clock differential input impedance z d 80 100 120 ? differential input clock amplitude (p-p) 640 - 1600 mv reference clock duty cycle 40 - 60 % reference clcok rise/fall time (20%-80%) t r /t r /t r f 200 - 1250 ps reference clock frequency f 0 f 0 f - baud/64 - mhz reference clock pin logic symbol name/description note 1 gnd module ground 1 2 vee5 optional -5.2v power supply (not used) 3 lvttl-i mod_desel module de-select; when held low allows module to respond to 2-wire interface 4 lvttl-o interrupt interrupt; indicates presence of an important condition which can be read over the 2-wire serial interface 2 5 lvttl-i tx_dis transmitter disable; turns off transmitter laser output 6 vcc5 +5v power supply 7 gnd module ground 1 8 vcc3 +3.3v power supply 9 vcc3 +3.3v power supply 10 lvttl-i/o scl 2-wire serial interface clock 2 11 lvttl-i/o sda 2-wire serial interface data line 2 12 lvttl-o mod_abs indicates module is not present. grounded in the module 2 13 lvttl-o mod_nr module not ready; indicating module operational fault 2 14 lvttl-o rx_los receiver loss of signal indicator 2 15 gnd module ground 1 16 gnd module ground 1 17 cml-o rd- receiver inverted data output 18 cml-o rd+ receiver non-inverted data output 19 gnd module ground 1 20 vcc2 +1.8v power supply 21 lvttl-i p_down/rst power down; when high, requires the module to limit power consumption to 1.5w or below. 2-wire serial interface must be functional in the low power mode. reset; the falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 vcc2 +1.8v power supply 23 gnd module ground 1 24 pecl-i refclk+ reference clock non-inverted input, ac coupled on the host board 25 pecl-i refclk- reference clock inverted input, ac coupled on the host board 26 gnd module ground 1 27 gnd module ground 1 28 cml-i td- transmitter inverted data input 29 cml-i td+ transmitter non-inverted data input 20 gnd module ground 1 pin out de? nition notes: 1. module ground pins gnd are isolated from the module case and chassis ground within the module. 2. shall be pulled up with 4.7k-10kohms to a voltage between 3.15v and 3.45v on the host boar d.
10 gbps 40km multirate xfp transceiver preliminary XP-MR-04-CDA 4 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 luminentoic.com lumnds644-nov0106 rev. 0. 1 pinout diagram h o s t p c b x f p p i n o u t t o p v i e w t o w a r d a s i c t o w a r d b e z e l 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 g n d m o d _ d e s e l i n t e r r u p t t x _ d i s v e e 5 v c c 5 g n d v c c 3 v c c 3 s c l s d a m o d _ a b s m o d _ n r r x _ l o s g n d g n d t d + t d - g n d g n d r e f c l k - r e f c l k + g n d v c c 2 p _ d o w n / r s t v c c 2 g n d r d + r d - g n d mechanical drawing .451 11.47 .150 3.80 .237 6.02 .246 6.25 .720 18.29 .272 6.91 .636 16.15 dimensions defined by xfp multisourcing agreement (msa). notes: unless otherwise specified luminenoic's xfp transceivers are compliant with the 1. .480 12.19 2.720 69.09 .332 8.44 77.98 3.070 .352 8.95 iso view
handling pr ecautions: this device is susceptible to damage as a result of electrostatic discharge (esd). a static free environment is highly recommended. follow guidelines according to proper esd procedures. laser safety: radiation emitted by laser devices can be dangerous to human eyes. avoid eye exposure to direct or indirect radiation. XP-MR-04-CDA 10 gbps 40km multirate xfp transceiver preliminary important notice! all information contained in this document is subject to change without notice, at luminentoic s sole and absolute discretion. luminentoic warrants performance of its products to current speci? cations only in accordance with the companys standard one-year warranty; however, speci? cations designated as preliminary are given to describe components only, and luminentoic expressly disclaims any and all warranties for said products, including express, implied, and statutory warran- ties, warranties of merchantability, ? tness for a particular purpose, and non-infringement of proprietary rights. please refer to the companys terms and conditions of sale for further warranty information. luminentoic assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. no license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and luminentoic makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. products described in this docu- ment are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. luminentoic customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify luminentoic for any damages resulting from such use or sale. the information contained in this document is provided on an as is basis. customer agrees that luminentoic is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. customer must contact luminentoic to obtain the latest version of this publication to verify , before placing any order, that the information contained herein is current. ? luminentoic, inc. 2003 all rights reserved 20550 nordhoff st. ? chatsworth, ca 91311 ? tel: 818.773.9044 ? fax: 818.576.9486 9f, no 81, shui lee rd. ? hsinchu, taiwan, r.o.c. ? tel: 886.3.5169222 ? fax: 886.3.5169213 5 luminentoic.com lumnds644-nov0106 rev. 0. 1 warnings legal notice ordering information part numbering de? nition: x p - m r - reach - temperature diagnostic revision x p = xfp mr = multi-rate c = commerical tem p (-5 to 70c) d = digital diagnostic 0 4 = 4 0km a = design revision
|
